By Harry ! Last Updated: July 01, 2021
Over a period of time, your pool can gather dirt and refuse at the lowest point of the pool. This can be not only annoying but also irritating. However, it's a desire for one to own a desirable pool. To eliminate this, you need to vacuum the pool for the cleanliness of your pool. Maintain your pool and be in a position to solve any pool problems. This post takes you through how to vacuum pool with sand filter.
The vacuum method is an excellent way to clean the pool and enhance the stableness of the pool. Often, dirt and scattered pieces can float on the surface of the pool at around 3-4 hours then later sinks. About this, one should vacuum their pool with a minimal rate for at least once a week.
Key Equipment Needed
Some equipment are needed to achieve a healthy pool. These include:
- Telescope pole,
- Vacuum hose pipe
- A vacuum head.
Must-Know Things Before Vacuuming Your Pool Using Sand Filter
Equipment in use for pool vacuuming needs to be strong and in good condition. This is for an easy way of cleaning the pool. For instance, the telescopic pole needs to be strong to withstand the cleaning process.
Telescope Pole
Additionally, the telescopic pole is a pole that is extended, covering different posts. It's through this equipment that cumbersome equipment such as ladders is opted out. Telescopic pole simplifies the workload hence having more access to cleaning.
Vacuum Hose Pipe
Having a vacuum hose pipe - a long pipe is recommended. This will make it easy for you to stroll around the pool's perimeter and have the hose pipe cover all the bottom part of the pool. With a long hose pipe, one can vacuum the pool at owns convenience.
Moreover, a hosepipe has a vacuum head for flexibility when it comes to cleaning a pool. The hosepipe, therefore, should be kept in good condition. To sustain it, you should ensure it's not clogged. In clogging cases, it may not have a strong suction performance.
However, there are high chances that the pipe may be at risk or get clogged. This is entailed through having debris stuck on the pipe through the cleaning process. This is in practice since the pipe is dependent on the movement of the air.
How Should you Clean a Clogged Hose Pipe?
In any case, at which the pipe is clogged, a cleaning process is done. First and foremost, clear out the clog. The hose is detached from the mechanism and then placed on the floor, preferably a tiled surface. It should be placed linearly.
Another step is cleaning the hosepipe. Hot water is preferred and should be deep at approximately 4 inches in depth to have it done. A bleaching agent and dish soap are of importance here. Mix all the ingredients, and the hose pipe should be submerged inside the sink. Eventually, clean the pipe.
Following the steps above, the last step involves rinsing the hose pipe. This involves flushing cold water through the inner part of the pipe. The water should flow through the pipe's length allowing the sludge out through the end of the pipe.
Since no equipment is prone to dangers, vacuum clogging can occur at any time. However, a perfect remedy to avoid clogging is having preventive measures at hand. It's advisable that one should have close checkups for the hose at least once in a month.
Vacuum Head
Another piece of equipment you need when vacuuming the pool is a vacuum head. It's modified with a hole that's used to screw either a pole or any attachments. Also, it has an opening cylindrical-like where the hose sticks. Vacuum heads come in different shapes.
They are either classified into rectangular or triangular. Typically, the shape of the vacuum head does not really matter. All have the same function in suctioning the dirt from the pool.
For you to achieve quite an easy cleaning procedure, we have one end of the hosepipe whereby the vacuum head is attached. It's in this advantage that one is able to have the vacuum head at the pool's bottom. On the head top, a clear space is needed to have it attached to the pole.
How to Use a Vacuum Head
Just have the hose pipe and vacuum head submerged into the water. Ensure that the pipe's other end is outer the pool. Besides, remember to have the other end of the hose into the water. It's advisable to have a quality vacuum pump head. This helps it to withstand extreme conditions such as sunny areas.
As it's the same case with other equipment, one needs to have a well-maintained vacuum head. However, it doesn't really need much attention. Some applicable steps are necessary to have it in good condition. This is useful to evade hefty maintenance costs.
Decent checkups are necessary. For instance, you should have the vacuum's canister checked and also the brush anytime you clean a pool. Replace some parts regularly. This will avoid filters getting clogged. Therefore, it enhances durability.
Vacuuming a Pool Using Sand Filter (Step-by-Step Guide)
There are several steps used in vacuuming a pool using a sand filter. Sand filters have quite many functions when maintenance of the pool is in question. Significantly, understanding how it works contributes towards cleaning of the pool. Plus, having the ability to choose a vacuum, and the right one is crucial.
Remove The Debris And Other Visible Materials
To start with, remove the debris and other visible materials. This is rather achieved by using a scooping net. It's used to remove these unwanted materials in the water, which could have blocked the vacuum head and also the hose pipe. Through this step, it's easy for the hose and vacuum head to create minimal chances for their clogging.
Vacuum Head Attached To Hose Pipe And Telescope Pole
Have the vacuum head attached to the hosepipe and telescope pole. You're required to have the pole held, and vacuum head lowered inside the pool. The hosepipe should accompany this into the water. To confirm efficiency, the bubbles start rising and immediately stops when the hose is water filled in the vacuum head.
Filling the hose with water comes with a significant reason behind it. The air could be trapped and otherwise creates air blocking in the pump. Therefore, you should have the hose held in your hands, as mentioned earlier, to fasten the filling of hosepipe with water.
Attaching The Hose Pipe On The Suction Port
The next step of vacuuming your pool is right here. It's on the suction port where you have the hose pipe attached. Other pools may not have the suction port. In such cases, you're required to vacuum your pool with a skimmer.
Vacuuming The Pool
Next, we have vacuuming of the pool. One is required to have the vacuum head moving in slow motion with the aid of the telescopic pole. This is done along the bottom surface of the pool and also at the sides of the pool. The need for slow motion is to ensure that the debris is not stirred up.
Disconnect The Hose Pipe From The Suction Point
Sequencely, the hose pipe is disconnected from the suction point. Through this process, you're required to have the hosepipe held vertically. As a result, your pool water will remain drained out. Advisable measures should be kept in place before storing, like rinsing it using a garden hosepipe. To sum up, allow it to dry up.
Turn Off Your Pipe
Nevertheless, don't forget to turn off the pump. Having your pump switched off after you vacuum your pool impacts towards avoiding disaster situations. For example, one could have the gasket diverting gadget in the valve broken.
BackWash The Filter
Following that, you also need to backwash the filter of the pool. In consequence, the filter valve is turned to backwash. Whenever we have sand filter, the sand inside may block the dirt and debris. The importance of having a backwash is to expel all the wastewater through a drain. This is achieved by reversing the flow of water.
Then, you need to have the pump turned on. Now, proceed with the backwash at most two minutes or so. Alternatively, the pump can remain on until all the water on the filter dries up. The period by which the pump stays on depends on how longer your filter takes to clean up.
Rinse
Switch the valve to rinse position from backwash through moving the valve. The rinse process can last for about one minute to achieve a satisfying mode. Through the process, any remaining debris stuck in the filter is flushed out.
Reset The Filter Valve & Turn On Your Pump
Lastly, the filter valve is set to filter, and the pump is turned on. Here, the filter is turned off to end the rinsing function. The pool starts filtering normally by switching the valve to filter position through turning on the filter.
Final Words
To sum things up, using a sand filter to vacuum a pool is a critical factor in enhancing a proper environment for the users. With poor pool maintenance, the pool can succumb to numerous unfriendly conditions.
Inclusively, algae building up and green water, just to mention a few. It's anyone's idea to have a great pool at their backyard. With this, you can host healthy external activities such as parties, fitness routines, and also for your fun.
